Cybex 11040 Eagle Leg Press User Manual

Cybex® Eagle Leg PressOwner’s ManualStrength SystemsPart Number 11040-999-4 B www.cybexintl.com

10Cybex Owner’s Manual6. Locate the belt attached near the adjusting tube.Set ScrewsBelt7. Loosen both set screws securing belt.8. Remove belt fro

11Cybex Owner’s Manual12. Move each half through the doorway to the desired location.13. Attach each half together using the eight BHSCS that were

12Cybex Owner’s Manual5. Remove the three Phillips head screws securing the top (back) shroud and carefully remove the shroud.Phillips HeadScrew (3)

13Cybex Owner’s Manual5. Lean guide rods outward, away from machine in order to provide the most room for installing weight plates.6. Slide top wei

14Cybex Owner’s Manual3. Slide belt through slot in belt clamp.4. Verify belt and insert are installed properly.Correct belt routing Wrong belt rou

15Cybex Owner’s ManualInstall back shrouds1. Place shroud back into position on the two bottom screws.Screw2. Install the top two screws securing t

16Cybex Owner’s Manual2. Align holes in decal with appropriate holes in weight stack. Do not allow the adhesive to touch weight stack at this time.3

17Cybex Owner’s ManualExerciseIntended UseThe intended commercial use of this machine is to aid exercise and improve general physical tness.Instruct

18Cybex Owner’s Manual CAUTION: Serious injury can result if precautions are not followed. Use equipment only as described in placards located on ea

19Cybex Owner’s ManualMaintenanceAll preventive maintenance activities must be performed on a regular basis. Performing routine preventive maintenanc

Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. Eagle® and its mark are registered trademarks of Cybex International,

20Cybex Owner’s ManualClean UpholsteryIf ThenLight Soiling1. Prepare a solution of 10% household liquid soap and warm water. 2. Apply with a soft d

21Cybex Owner’s ManualGuidelines for cleaning front panel: Use clean soft cloths or sponges for application of cleaners and again for washing and rin

22Cybex Owner’s Manual WARNING: Equipment hazard. To avoid serious injury or death replace worn or damaged components immediately and keep the equip

23Cybex Owner’s ManualBeltsCondition of Belt 3D View 3D or Side ViewPeeling of the belt’s skin.Wave in beltBelt is necked down (narrow section) Repl

24Cybex Owner’s Manual CAUTION: Worn handles• Do not use handles if less then 1/8” of material remains on edge.• Replace all worn handles immediat

25Cybex Owner’s ManualCable AdjustmentTools Required9/16” Wrench (2) Four types of cable tension adjustment are used on Cybex Strength Systems:Cable

26Cybex Owner’s ManualBelt AdjustmentTools Required• 7/32” Wrench• Torque wrench (lbs-in)Belt Adjustment ActionLoose Belt1. Using a 7/32” Allen wr

27Cybex Owner’s ManualCustomer ServiceProduct RegistrationTo register product do the following:1. Visit www.cybexintl.com.2. Locate Product Registr

28Cybex Owner’s ManualReturn Material Authorization (RMA)The Return Material Authorization (RMA) system is used when returning material for placement

Cybex Owner’s Manual 3SafetySafety Guidelines and PracticesRead the Owner’s Manual carefully before assembling, servicing, or using the equipment. Own

10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183 www.cybexintl.com

Cybex Owner’s Manual 4It is the responsibility of the facility owner/owner of the equipment to ensure that there is appropriate clearance around each

Cybex Owner’s Manual 5• DO NOT lean or pull on machine• DO NOT use machine for support during stretching.• DO NOT attach resistance straps, ropes

6Cybex Owner’s ManualWarnings and CautionsWarning decals indicate a potentially hazardous situation that could result in death or serious injury if t

7Cybex Owner’s ManualLabel PlacementITEM NO. QTY. PART NUMBER DESCRIPTION111 4 HT572512TAP SC NO. 10-24 X .50 PN HD PHIL110 4 HN575100LOCKNUT .190-N

8Cybex Owner’s ManualAssemblyMachine SpecificationsTotal Weight and Size: Eagle 11040 Leg PressWeight Machine Dimensions at Rest Machine Dimensions a

9Cybex Owner’s ManualQty Part Number Description Diagram1 12000-560Decal, Weight Plate (30-290)125 OWATONNA MFG. APPR. TECH. PUBS. APPR. DATE DATE R