VR3® Cable ColumnOwner’s ManualStrength SystemsPart Number 12220-999-4 Lwww.cybexintl.com
Cybex Owner’s Manual 10Move to desired locationIf ThenIf machine can be moved without adding or removing weight stacks.Two people will be required for
Cybex Owner’s Manual 11SecurelyanchormachinetotheoorCybex strongly recommends to maximize stability, equipment must be secured to a solid level
Cybex Owner’s Manual 12Cable routing1. Verify cable is routed through pulley brackets. 2. Verify cable is not twisted. 3. Place weight stack pin in
Cybex Owner’s Manual 13Install weight plate decals1. Peel off back side of decal making sure that the decals remain attached to the front sticker.Fro
14Cybex Owner’s Manual ExerciseIntended UseThe intended commercial use of this machine is to aid exercise and improve general physical tness.Instr
15Cybex Owner’s Manual Direction of cable represents direction of forceArm CurlStartFinishLateral RaiseStartFinishArm ExtensionStart Finish
16Cybex Owner’s ManualMaintenanceAll preventive maintenance activities must be performed on a regular basis. Performing routine preventive maintenanc
17Cybex Owner’s ManualClean UpholsteryIf ThenLight Soiling1. Prepare a solution of 10% household liquid soap and warm water. 2. Apply with a soft d
18Cybex Owner’s ManualGuidelines for cleaning front panel: Use clean soft cloths or sponges for application of cleaners and again for washing and rin
19Cybex Owner’s Manual WARNING: Equipment hazard. To avoid serious injury or death replace worn or damaged components immediately and keep the equip
Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. VR3® and its mark are registered trademarks of Cybex International, I
20Cybex Owner’s ManualBeltsCondition of Belt 3D View 3D or Side ViewPeeling of the belt’s skin.Wave in beltBelt is necked down (narrow section) Repl
21Cybex Owner’s Manual CAUTION: Worn handles• Do not use handles if less then 1/8” of material remains on edge.• Replace all worn handles immediat
22Cybex Owner’s ManualCable AdjustmentTools Required9/16” Wrench (2) Four types of cable tension adjustment are used on Cybex Strength Systems:Cable
23Cybex Owner’s ManualBelt AdjustmentTools Required• 7/32” Wrench• Torque wrench (lbs-in)Belt Adjustment ActionLoose Belt1. Using a 7/32” Allen wr
24Cybex Owner’s ManualCustomer ServiceProduct RegistrationTo register product do the following:1. Visit www.cybexintl.com.2. Locate Product Registr
25Cybex Owner’s ManualReturn Material Authorization (RMA)The Return Material Authorization (RMA) system is used when returning material for placement
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183 www.cybexintl.com
Cybex Owner’s Manual 3SafetySafety Guidelines and PracticesRead the Owner’s Manual carefully before assembling, servicing, or using the equipment. Own
Cybex Owner’s Manual 4It is the responsibility of the facility owner/owner of the equipment to ensure that there is appropriate clearance around each
Cybex Owner’s Manual 5• DO NOT lean or pull on machine• DO NOT use machine for support during stretching.• DO NOT attach resistance straps, ropes
6Cybex Owner’s ManualWarnings and CautionsWarning decals indicate a potentially hazardous situation that could result in death or serious injury if t
7Cybex Owner’s ManualLabel PlacementDE000001-X8500-025-XDE000005-X
Cybex Owner’s Manual 8AssemblyMachine SpecificationsTotal Weight and Size VR3 Cable Column 12220 Standard StackWeight Machine Dimensions at Rest Machi
Cybex Owner’s Manual 9The dimensions stated in the assembly instructions of this manual include the maximum foot print (in use) dimensions.• Area is
Comments to this Manuals