VR3® Arm ExtensionOwner’s ManualStrength SystemsPart Number 12080-999-4 Nwww.cybexintl.com
Cybex Owner’s Manual 10Qty Part Number Description Diagram17 4000C101 Weight Stack Plate (Standard)9638WEIGHT PLATE DETAILLIGHT STACK 13000-032STANDAR
Cybex Owner’s Manual 11Move to machine to the desired location1. Remove the four shipping cones using a 3/4” socket or wrench.2. Attach foot pads to
Cybex Owner’s Manual 123. Slide belt through slot in belt clamp.4. Verify belt and insert are installed properly. Do not install the insert backward
Cybex Owner’s Manual 132. Insert a guide pin through each hole of the template. A guide pin can be anything that ts through the weight stack hole, s
14Cybex Owner’s Manual ExerciseIntended UseThe intended commercial use of this machine is to aid exercise and improve general physical tness.Instr
15Cybex Owner’s ManualMaintenanceAll preventive maintenance activities must be performed on a regular basis. Performing routine preventive maintenanc
16Cybex Owner’s ManualClean UpholsteryIf ThenLight Soiling1. Prepare a solution of 10% household liquid soap and warm water. 2. Apply with a soft d
17Cybex Owner’s ManualGuidelines for cleaning front panel: Use clean soft cloths or sponges for application of cleaners and again for washing and rin
18Cybex Owner’s Manual WARNING: Equipment hazard. To avoid serious injury or death replace worn or damaged components immediately and keep the equip
19Cybex Owner’s ManualBeltsCondition of Belt 3D View 3D or Side ViewPeeling of the belt’s skin.Wave in beltBelt is necked down (narrow section) Repl
Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. VR3® and its mark are registered trademarks of Cybex International, I
20Cybex Owner’s Manual CAUTION: Worn handles• Do not use handles if less then 1/8” of material remains on edge.• Replace all worn handles immediat
21Cybex Owner’s ManualCable AdjustmentTools Required9/16” Wrench (2) Four types of cable tension adjustment are used on Cybex Strength Systems:Cable
22Cybex Owner’s ManualBelt AdjustmentTools Required• 7/32” Wrench• Torque wrench (lbs-in)Belt Adjustment ActionLoose Belt1. Using a 7/32” Allen wr
23Cybex Owner’s ManualCustomer ServiceProduct RegistrationTo register product do the following:1. Visit www.cybexintl.com.2. Locate Product Registr
24Cybex Owner’s ManualReturn Material Authorization (RMA)The Return Material Authorization (RMA) system is used when returning material for placement
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183 www.cybexintl.com
Cybex Owner’s Manual 3SafetySafety Guidelines and PracticesRead the Owner’s Manual carefully before assembling, servicing, or using the equipment. Own
Cybex Owner’s Manual 4It is the responsibility of the facility owner/owner of the equipment to ensure that there is appropriate clearance around each
Cybex Owner’s Manual 5• DO NOT lean or pull on machine• DO NOT use machine for support during stretching.• DO NOT attach resistance straps, ropes
6Cybex Owner’s ManualWarnings and CautionsWarning decals indicate a potentially hazardous situation that could result in death or serious injury if t
7Cybex Owner’s ManualLabel Placement4520-362-XDE000001-XDE000005-X8500-025-X
Cybex Owner’s Manual 8AssemblyMachine SpecificationsTotal Weight and Size VR3 Arm Extension 12080 Standard StackWeight Machine Dimensions at Rest Mach
Cybex Owner’s Manual 9In compliance with the ADA (American Disabilities Act) there must be clear floor space of at least 30 by 48 inches and be served
Comments to this Manuals