Bravo™ 8800/8810 Owner’s ManualStrength SystemsPart Number 8800-999-4 Lwww.cybexintl.com
10Cybex Owner’s ManualAssembly ProcedureRead and understand all instructions thoroughly before assembling this unit.Verify parts list shown below.Qty
11Cybex Owner’s ManualMove to desired locationIf ThenIf machine can be moved without adding or removing weight stacks.Two people will be required for
12Cybex Owner’s ManualIf ThenIf machine needs weight stacks removed before moving to desired location.5. Repeat procedure for opposite guide rods.6.
13Cybex Owner’s ManualCable routing1. Verify cable is routed through top of pulley bracket and then route cable end to top weight connector.2. Pul
14Cybex Owner’s Manual3. Place weight stack pin in each plate to verify proper installation.4. Lift top weight up and down simulating normal operat
15Cybex Owner’s ManualIf Then8800/8810cantthrough a doorwayTwo people will be required for this procedure1. Move to desired location.2. Remove
16Cybex Owner’s ManualIf Then8810cannottthrough a doorway1. Remove the four shipping cones using a 3/4” socket or wrench.2. Place foot pads on
17Cybex Owner’s ManualExerciseIntended UseThe intended use of this machine is to aid or improve general physical tness and exercise for commercial u
18Cybex Owner’s ManualSEATED PRESSARM CURLARM EXTENSIONTRUNK ROTATIONHIP ABDUCTIONSQUATHIP FLEXION-KNEE EXTENSIONHIP ADDUCTION
19Cybex Owner’s ManualTRUNK FLEXIONHIP EXTENSION-KNEE FLEXIONTRUNK EXTENSION
Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc.Bravo® and its mark are registered trademarks of Cybex International,
20Cybex Owner’s ManualMaintenanceAll preventive maintenance activities must be performed on a regular basis. Performing routine preventive maintenanc
21Cybex Owner’s ManualClean UpholsteryIf ThenLight Soiling1. Prepare a solution of 10% household liquid soap and warm water. 2. Apply with a soft d
22Cybex Owner’s ManualGuidelines for cleaning front panel: Use clean soft cloths or sponges for application of cleaners and again for washing and rin
23Cybex Owner’s Manual WARNING: Equipment hazard. To avoid serious injury or death replace worn or damaged components immediately and keep the equip
24Cybex Owner’s ManualBeltsCondition of Belt 3D View 3D or Side ViewPeeling of the belt’s skin.Wave in beltBelt is necked down (narrow section) Repl
25Cybex Owner’s Manual CAUTION: Worn handles• Do not use handles if less then 1/8” of material remains on edge.• Replace all worn handles immediat
26Cybex Owner’s ManualCable AdjustmentTools Required9/16” Wrench (2) Four types of cable tension adjustment are used on Cybex Strength Systems:Cable
27Cybex Owner’s ManualBelt AdjustmentTools Required• 7/32” Wrench• Torque wrench (lbs-in)Belt Adjustment ActionLoose Belt1. Using a 7/32” Allen wr
28Cybex Owner’s ManualCustomer ServiceProduct RegistrationTo register product do the following:1. Visit www.cybexintl.com.2. Locate Product Registr
29Cybex Owner’s ManualReturn Material Authorization (RMA)The Return Material Authorization (RMA) system is used when returning material for placement
Cybex Owner’s Manual 3SafetySafety Guidelines and PracticesRead the Owner’s Manual carefully before assembling, servicing, or using the equipment. Own
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183 www.cybexintl.com
Cybex Owner’s Manual 4It is the responsibility of the facility owner/owner of the equipment to ensure that there is appropriate clearance around each
Cybex Owner’s Manual 5• DO NOT lean or pull on machine• DO NOT use machine for support during stretching.• DO NOT attach resistance straps, ropes
6Cybex Owner’s ManualWarnings and CautionsWarning decals indicate a potentially hazardous situation that could result in death or serious injury if t
7Cybex Owner’s ManualLabel Placement8500-025-X 8810 Chin-Up Bar8800-442-XDE000001-X8500-025-X 8500-025-X DE000005-X
8Cybex Owner’s ManualAssemblyMachine SpecificationsDimensions/Weight 8800 At Use And At Rest 8810 At Use And At RestL x W x H 45” L 54” W x 77” H 45”
9Cybex Owner’s ManualAll other machines must have a clear floor space of 23” for all access point on the machine, unless shown in the Owner’s Manual.
Comments to this Manuals